Used machines Germany - Innovac GmbH

Innovac GmbH Used machines from Germany

i.e. Machining Center MORI SEIKI

Innovac used-machines

Latest Offers [281 - 300 of 3028]

Plasma Cutter

Kjellberg Finsterwalde FineFocus 800

Germany

2008

used

on request

INNO31780

Mains voltage: 3x 400V, 50Hz, fuse protection: 125A slow-blow, maximum connected load: 83kVA, cutting current at 100% duty cycle: 80 to 300A, output voltage: 112 to 200V, rated output current: 300A, duty cycle: 100%, maximum input current: 120A, protection class: IP22, insulation class: F, cooling method: AF (air cooling), no-load power consumption: 1.3kW, maximum operating pressure: 0.55MPa (5.5bar), impulse withstand voltage (Up): 17kV, plasma torch: PB-S80 W, compatible plasma gases: O₂, air, Ar, H₂, compatible swirl gases: air, N₂, length: 1375mm, width: 870mm, height: 1505mm, weight: 556kg. Inspection on site is possible.

CNC Lathe

Emco Turn E25

Germany

2007

used

on request

INNO31779

A CNC short-bed turning machine Emco is available. Travel X/Z: 100mm/300mm, max. turning diameter: 85mm, max. swing diameter: 250mm, max. turning length: 255mm, center distance: 405mm, max. bar capacity: 25.5mm, spindle bore: 30mm, spindle speed: 6300rpm, tool stations: 12, tool interface: VDI16, rapid traverse: 15m/min. Machine dimensions X/Y/Z: approx. 1700mm/1300mm/1850mm, weight: approx. 1400kg, control: Siemens Sinumerik 810D, operating hours: approx. 27000h, spindle hours: approx. 11000h. Including bar feeder. The spindle was replaced in 2021 at approx. 25000 operating hours. Documentation available. An on-site inspection is possible.

CNC Vertical Machining Center

Dmg Mori DMC 835 V

Germany

2009

used

on request

INNO31778

A vertical CNC machining center DMG Mori is available. Travel X/Y/Z: 835mm/510mm/510mm, table dimensions X/Y: 1000mm/560mm, max. table load: 800kg, tool holder: SK40, spindle speed: 10000rpm, tool stations: 30, rapid traverse: 30m/min, positioning accuracy: +/-0.008mm, repeatability: +/-0.005mm. Machine dimensions X/Y/Z: approx. 3700mm/2450mm/2750mm, weight: approx. 4100kg, control: Heidenhain iTNC530, operating hours: approx. 16000h, spindle hours: approx. 8000h. Including chip cart, chip conveyor and belt filter. Documentation available. An on-site inspection is possible.

Steam Generator

Clayton SEG-354-1

Germany

2010

used

on request

INNO31777

Operating pressure: 10bar, test pressure (PT): 15bar, steam temperature (TS): 184°C, water content: 916l, steam output: 5480kg/h, heating surface (HS): 73.4m², heat output: 3437kW, maximum burner capacity: 3772kW, minimum burner capacity: 1320kW, gas regulator pressure: 150mbar, burner gas pressure: 5 to 65mbar, nominal gas consumption: 406.9Nm³/h, current consumption: 46.2A, length: 3000mm, width: 1900mm, height: 3300mm. Inspection on site is possible.

Needle Loom

Dilo OD-II HVL 55 / OUG-II S50 / OD-II 55

Germany

2000

used

on request

INNO31776

3 Dilo needle looms are offered. 1) Pre-needling and finish-needling machine Dilo, DILOOM OD-II HVL 55, year of manufacture: 2000, number of needle boards: 2, working width: 5500mm, max. stroke frequency: 1000strokes/min, needle beam stroke: 60mm, needle board width: 200mm each, needle distribution range: approx. 3000-5000needles/m. 2) Double needle loom Dilo, DI-LOOM OUG-II S50, year of manufacture: 2000, working width: 5000mm, number of needle boards: 4, needle beam stroke: 60mm, max. stroke frequency: 1200strokes/min, needle density: approx. 18000needles/linear m. 3) Pre-needling and finish-needling machine Dilo, DI-LOOM OD II 55, year of manufacture: 1998, working width: 5500mm, needling system: Downstroke, number of needle boards: 2, needle beam stroke: 60mm, max. stroke frequency: 1200strokes/min, needle board width: 200mm each. Inspection possible by appointment.

Steam Generator

Certuss JUNIOR

Germany

1996

used

on request

INNO31775

Throughput capacity: 600kg/h, permissible operating pressure: 16bar, fuel: oil, length: 1600mm, width: 1000mm, height: 1900mm. Inspection on site is possible. The machine is not under power.

CNC Machining Center

Metrom PG 2000

Germany

2007

used

on request

INNO31773

A CNC 5-axis pentapod machining center Metrom is available. Axes: 5, Travel X/Y/Z/V: 1600mm/2800mm/1000mm/3200mm, A-axis swivel: 90°, Table dimensions X/Y: 1600mm/1800mm, Tool interface: HSK63, Speed: 15000rpm, Spindle power: 25kW/32kW. Machine dimensions X/Y/Z: approx. 6500mm/4000mm/4500mm, Weight: approx. 14000kg, Control: Andronic 2060. Including enlarged worktable, coolant system with 200l tank, Blum TC 50 3-D touch probe, additional holder and milling spindle. Documentation available. An on-site inspection is possible.

CNC Machining Center

Hedelius BC60

Germany

1998

used

on request

INNO31772

A Hedelius CNC 3-axis machining center is available. Travel X/Y/Z: 2490mm/630mm/750mm, table dimensions X/Y: 3200mm/650mm, tool holder: SK40, spindle speed: 8000rpm, tool positions: 48, coolant tank volume: 350l. Machine dimensions X/Y/Z: approx. 6500mm/3700mm/3700mm, weight: approx. 16500kg, control: Heidenhain TNC426. Including coolant tank, divided working area, chip conveyor and through-tool coolant. Documentation available. An on-site inspection is possible.

CNC EDM-Machine

Agie Agiecut Excellence 3

Germany

2002

used

on request

INNO31771

Travel X/Y/Z: 500mm/3590mm/250mm, wire diameter range: 0.15mm-0.3mm, max. workpiece dimensions X/Y/Z: 1050mm/650mm/250mm, max. workpiece weight: 400kg/800kg, max. taper: 30°/100mm, wire speed: 300mm/s, max. surface quality: Ra 0.1µm. Machine dimensions X/Y/Z: approx. 2800mm/2400mm/2250mm, weight: approx. 4500kg, control: Agie, operating hours: approx. 151182h. Documentation available. An on-site inspection is possible. The image is an example.

CNC Universal Lathe

Traub TNA 400

Germany

2002

used

on request

INNO31770

A relatively lightly used Traub CNC universal lathe is available. Spindle bore: 82mm, max. chuck diameter: 315mm, turning length: 750mm, X/Z travel: 360mm/750mm, Z-axis travel: +/-60mm, rapid traverse: 20m/min. Machine dimensions X/Y/Z: approx. 3250mm/1900mm/2300mm, weight: approx. 7800kg, operating hours: approx. 21812h. Documentation available. An on-site inspection is possible. The image is for reference only.

Cleaning System

Mafac Elba

Germany

2023

used

on request

INNO31769

A Mafac two-tank spray flood cleaning machine is available. Basket dimensions X/Y/Z: 660mm/480mm/338mm, max. batch weight: 100kg, tank volume 1/2: 425l/300l, machine dimensions X/Y/Z: approx. 1850mm/1400mm/1800mm, weight: approx. 1000kg, operating hours: 4531h. Documentation available. An on-site inspection is possible.

CNC Coordinate Measuring Machine

Mitutoyo Crysta-Apex

Germany

2023

used

on request

INNO31768

A Mitutoyo CNC bridge coordinate measuring machine is available. Travel X/Y/Z: 1200mm/2000mm/1000mm, measuring volume: 2.4m³, max. workpiece weight: 2500kg, max. workpiece height: 1000mm, probe system: Renishaw, probe positions: 20, measuring accuracy: 2.3+/-0.3/100µm, max. travel speed: 693mm/s. Machine dimensions X/Y/Z: approx. 3400mm/2200mm/3600mm, weight: approx. 6150kg, control: Mcosmos-3 V4.3. Documentation available. An on-site inspection is possible.

Suction Unit

Höcker Polytechnik Vacumobil VT 140/160-L

Germany

2019

used

on request

INNO31767

A mobile Höcker dust extraction and filtration unit is available. Inlet diameter: 140mm/160mm, max. airflow: 1950m³/h, max. vacuum: 2600Pa, filter category: H3, machine dimensions X/Y/Z: approx. 1450mm/1050mm/2000mm, weight: approx. 350kg. Documentation available. An on-site inspection is possible.

PVD Coating System

Platit Pi111 Plus G3

Germany

2023

used

on request

INNO31766

A complete PVD hard coating system including peripheral equipment is available. 1) PVD hard coating system Platit Pi111 Plus G3, year of manufacture: 2023, deposition process: ARC, cathodes: 2, targets: 2, max. coating diameter: 353mm, max. coating height: 498mm, max. load: 160kg, max. workpiece diameter: 355mm, machine dimensions X/Y/Z: approx. 1950mm/1600mm/2250mm, control system: Platit. 2) Screw compressor Almig F-Drive 22, year of manufacture: 2022, flow rate: 4.14m³/min, final pressure range: 5bar-13bar, motor power: 22kW. 3) Compressed air receiver OKS, year of manufacture: 2023, volume: 1000l, operating pressure min./max.: 0bar/11bar, test pressure: 16bar. 4) Blast cabinet MHG SMG50, year of manufacture: 2024. 5) Osmosis Pro water filtration unit. Documentation available. An on-site inspection is possible.

Lamella Clarifier

Artinox

Germany

unknown

used

on request

INNO31765

Two Artinox inclined clarifier/lamella clarifier systems made of stainless steel are offered for the continuous mechanical separation of dirt particles, sludge, or sediments from water or process liquids. 1) Artinox inclined clarifier/lamella clarifier, pipe connection: Ø 108mm, additional connection: Ø 168mm, main module dimensions: approx. 2400mm/1350mm/2360mm, hopper width bottom/top/center: approx. 1323mm/1896mm/1546mm, inclination: approx. 1.1°, function: solid-liquid separation by sedimentation, application: process water, wastewater, wash water, liquids containing settleable solids, separation principle: sedimentation with lamella packs/inclined plates, flow direction: horizontal, lamella packs: available, sedimentation hopper: available, equipped with multiple basin modules, lamella clarifier sections, sludge hopper, upper pipe distributor, connection nozzles and flanges, lifting lugs, frame, maintenance access. 2) Artinox inclined clarifier/lamella clarifier, smaller module dimensions: approx. 2300mm/1250mm/1371mm, hopper height/inclined bottom section: approx. 1050mm, inner/lower hopper dimension: approx. 775mm, lamella/sheet spacing: approx. 293mm, function: separation of settleable solids from liquids, design: rectangular clarification tank with hopper bottom, flow path: via inlet, clarification zone, overflow edge, sludge hopper: available, separate pre-collection tank: available on the side, discharge pipe/flange connection: available, maintenance ladder: available, wooden cover: available, equipped with main clarification tank, hopper bottom, side-mounted attachment tank, pipe connection, flange, maintenance ladder, upper cover. Inspection possible by appointment.

Drag Finishing Machine

Tinkap Pardus 2H12T-R

Germany

2015

used

on request

INNO31764

One Tinkap drag finishing machine is available. Tools: 12/cycle, Throughput: approx. 144tools/h, Clamping range: 42mm, Max. tool length: 250mm, Processing heads: 2, Tool holders: 2x6. Documentation available. An on-site inspection is possible.

Centrifuge System

Ruma MZ 90-B 300

Germany

2006

used

on request

INNO31763

Offered is a Ruma cleaning centrifuge system with cooling unit and pump system for cleaning cooling lubricants, grinding oils, emulsions, wash water and process fluids. Max. achievable cleanliness level: approx. 1µm, suitable media: oils, emulsions, cooling lubricants, wash water, process fluids, max. rotor speed: 3620rpm, rotor diameter: 310mm, max. solids capacity: 12kg, main motor power: 2.2kW, filter aids: not required, separation principle: solid-liquid separation by centrifugal force. Machine weight: 400kg. Documentation available. Inspection possible by arrangement.

Fine Filtration System

Vomat FA120 EKS

Germany

2019

used

on request

INNO31762

A compact Vomat fine filtration system for grinding oil and coolant with full-flow filtration using the backflushing process and a cooling unit is available. Filtration capacity: 240l/min, Filtration fineness: 3µm-5µm, Filling capacity: 500l, Machine dimensions X/Y/Z: approx. 1600mm/1000mm/1200mm, Weight: approx. 500kg. Documentation available. An on-site inspection is possible.

Planing Machine

Cleveland GAPU-5

Germany

2024

used

on request

INNO31761

A Cleveland dressing and profiling machine for machining diamond and CBN grinding wheels is available. Dressing process: dry, max. single wheel dimensions X/Y: 400mm/30mm, max. wheel package dimensions X/Y: 150mm/150mm, grinding spindle diameter: 80mm, wheel flange bore: 32mm. Machine dimensions X/Y/Z: approx. 2200mm/1700mm/2000mm, weight: approx. 850kg. Documentation available. An on-site inspection is possible.

Shop Crane

Shop Crane SC2000C

Germany

2017

used

on request

INNO31760

A workshop crane is offered for lifting and maneuvering engines, assemblies, machine components, and heavy workshop parts. Max. lifting capacity: 2000kg, Load capacity per boom position: 2000kg/1700kg/1500kg, Design: mobile and foldable, Min./max. hook height: 175mm/2490mm, Leg height: 208mm, Boom: telescopic, Min./max. boom length: approx. 1295mm/1595mm, Weight: 165kg, Overall dimensions in working position: X/Y/Z: approx. 1900mm/1170mm/2490mm. Inspection possible by appointment.