Vertical Injection Moulding Machine

Cronoplast BABYPLAST 6/10VP

Germany

2009

used

on request

INNO32395

Mains voltage: 400V, 3L+N, 230V, 3L, rated current: 7.5A at 400V, 11A at 230V, frequency: 50/60Hz, short-circuit breaking capacity: 3.5kA, weight: 370kg, an on-site inspection is possible.

more

Injection Moulding Machine

Demag Ergotech Systec 170/520-600 PinkLine

Germany

2008

used

on request

INNO32389

A hydraulic injection molding machine is offered. Tie-bar spacing: 520mm x 520mm, clamping force: 1700kN, locking force: 1870kN, max. opening stroke: 500mm, mold height min./max.: 275mm/585mm, screw diameter: 45mm, injection pressure: 1914bar, shot weight: 294g (PS), centering ring: 160mm, oil tank capacity: 400l, control: NC5. Equipped with robot system DR721-1278 (Wittmann W721, year of manufacture 2008, travel X/Y/Z: 550mm/1000mm/2000mm), 8-zone hot runner control, 8 cooling connections, 2 core pulls. Weight: approx. 6900kg, overall dimensions X/Y/Z: approx. 5300mm/1600mm/2000mm. Inspection is possible by prior arrangement.

more

Mould carrier

Optitek F1 4060-600 800

Germany

2007

used

on request

INNO32384

Two Optitek mould carriers with a control unit in the middle are offered. Opening width min./max.: 600mm/800mm, operating pressure: 6bar, hydraulic pressure: 50bar-200bar, max. clamping force at 200bar: approx. 779.8kN, max. opening force at 200bar: approx. 978.3kN, power supply: 400V/32A. Dimensions X/Y/Z: approx. 2500mm/2050mm/2799mm. The mold carrier is used for handling PU foaming molds. Documentation available. Inspection possible by arrangement.

more

Injection Moulding Machine

Krauss Maffei KM 80-220 C2

Germany

1999

used

on request

INNO32381

Clamping force: 80t, 3-phase mains supply: 400V, 50Hz, total rated current: 130A, upstream fuse: 160A, max. motor current: 30A, an on-site inspection is possible. The machine is located in Hungary.

more

Vacuum Dryer

Maguire VBD-150

Germany

2017

used

on request

INNO32371

A Maguire vacuum dryer for plastic granulate is offered. Throughput: approx. 65kg/h, heating power: 11kW, max. operating temperature: 190°C, heating hopper volume: 70l, vacuum chamber volume: 28l, retention hopper volume: 45l, voltage: 400V/3Ph, frequency: 50Hz, current consumption: 9.7A. An on-site inspection is possible.

more

Injection Moulding Machine

Krauss Maffei KM 350-1400-390 CZ

Germany

2005

used

on request

INNO32352

Max. locking force: 3500kN, clear tie-bar spacing: 710x710mm, min. mold height: 380mm, max. opening stroke: 1300mm minus mold height, max. ejector stroke: 250mm, max. ejector force: 95kN, ejector retraction force: 48kN, rotary table diameter: 890mm, screw diameter K1: 60mm, K2: 35mm, nozzle radius: 15mm, max. injection pressure K1: 2000bar, K2: 2429bar, max. shot weight (PS) K1: 618g, K2: 142g, hot runner: external, core pull connection: DNP Flatface BG3 (large flat-face sealing), centering mandrel: AS + DS, weight: 16.37t, total operating hours: 74,276h, production hours: 66,341h, the second injection unit and the rotary table have not been used for five years, with documentation and linear handling system, regularly maintained in-house. An on-site inspection is possible, the machine is not connected to power.

more

Injection Moulding Machine

Mannesmann Demag D 650-4500

Germany

1995

used

on request

INNO32348

Clamping force: 6500kN, locking force: 7150kN, max. opening stroke: 930mm, mold height: 360-920mm, max. distance between mold mounting platens: 1850mm, mold mounting platens: 1350x1350mm, clear tie-bar spacing: 900x900mm, max. mold weight: 8.6t, max. weight on moving mold mounting platen: 5.7t, screw diameter: 110mm, L/D ratio: 17.2, injection pressure: 1270bar, shot volume: 3570cm³, shot weight (PS): 3180g, max. metering stroke: 375mm, max. nozzle stroke: 850mm, nozzle immersion depth (SVO): 70mm, nozzle contact force: 200kN, installed barrel heating capacity: 52kW, hopper capacity: 110l, the machine screw is defective. With documentation. An on-site inspection is possible.

more

Injection Mould

W23630, W23635, W61014F2, W61015F5, W61019, W62539

Germany

unknown

used

on request

INNO32322

A package of six injection moulds for the series production of office organization products is available. The molds can be used to manufacture nestable filing trays, PET filing trays A4-C4, high-gloss and matte PS filing trays, a frame for a 3-tier filing tray unit, and a PET desk organizer. Materials processed: PET, recycled PET and PS. Mold numbers: W23630, W23635, W61014F2, W61015F5, W61019 and W62539. Mold dimensions depending on the mold: 397-570mm × 396-820mm × 369-637mm. Mold weights where documented: 450-1450kg. Average cycle times: 24.4-43.2s. Machine classes previously used where documented: 250t, 275t and 380t. According to the available documentation, the molds are in good condition. W61019 is used exclusively to manufacture the frame for the 3-tier filing tray unit. The molds are sold as a complete package. An on-site inspection of the molds is possible by arrangement.

more

Injection Moulding Machine

Krauss Maffei Extra 80-380

Germany

unknown

used

on request

INNO32321

Clamping force: 800kN, an on-site inspection is possible.

more

Vulcanizing Press

Wickert WKP 2560/5/2,5

Germany

1993

used

on request

INNO32318

Press force: 2800kN, heating platen size X/Y: 500mm/500mm, daylight between the heating platens: 200mm, max. hydraulic pressure: 300bar, heating power: 9.4kW, drive power: 7.5kW, control: Siemens S5 with OP17, weight: approx. 5000kg. Equipped with sliding table, vacuum pump, vacuum chamber and vacuum receiver tank. An on-site inspection is possible.

more

Vulcanizing press

Wickert WKP 2560/5/2,5

Germany

1990

used

on request

INNO32317

Press force: 2800kN, heating platen size X/Y: 500mm/500mm, daylight between the heating platens: 200mm, max. hydraulic pressure: 300bar, heating power: 9.4kW, drive power: 7.5kW, control: Siemens S5 with OP17, weight: approx. 4500kg. Equipped with sliding table, vacuum pump, vacuum chamber and vacuum receiver tank. An on-site inspection is possible.

more

Injection Moulding Machine

Arburg ALLROUNDER CENTEX 470C 1500-350/150

Germany

2005

used

on request

INNO32310

Clamping force: 1500kN, rated current: 133A, connected load: 74kW, an on-site inspection is possible.

more

Injection Moulding Machine

Krauss Maffei KM 65-380 CX

Germany

2008

used

on request

INNO32309

Clamping force: 650kN, length: 4000mm, width: 1600mm, height: 2200mm, weight: 3.9t, an on-site inspection is possible.

more

Injection Moulding Machine

Krauss Maffei KM 160-1000 CX

Germany

2005

used

on request

INNO32308

Clamping force: 1600kN, width: 1600mm, height: 2200mm, weight: 6.8t, an on-site inspection is possible.

more

Injection Moulding Machine

Demag Ergotech 1250-440 concept

Germany

2001

used

on request

INNO32307

Clamping force: 1250kN, tie-bar spacing: 475x450mm, injection unit: 440, max. flow rate: 100l/min, max. hydraulic pressure: 190bar, weight: 6.6t, an on-site inspection is possible.

more

Injection Moulding Machine

Demag Ergotech Extra 80-430

Germany

2004

used

on request

INNO32306

Clamping force: 800kN, tie-bar spacing: 400mm, injection unit: 430, max. flow rate: 76l/min, max. hydraulic pressure: 210bar, control: CDIAS, weight: 3.6t, an on-site inspection is possible.

more

Thermoplastic Injection Moulding Machine

Polyapress

Germany

unknown

used

on request

INNO32260

Condition: used, with visible signs of use, was operational until placed in storage, control voltage: 24V, operating voltage: 230V, frequency: 50Hz, CO₂ pressure: 10bar, connected load: 500W, with CE marking. An on-site inspection is possible.

more

Injection Moulding Machine

Battenfeld TM 4500/3300

Germany

2004

used

on request

INNO32239

A BATTENFELD large-format horizontal injection molding machine in need of repair is offered. Operating pressure: 210bar, clamping force: 4500kN, screw diameter: 85mm, injection volume: 2128cm³, injection pressure: 1624bar, tie-bar spacing X/Y: 900mm/800mm, opening stroke: 950mm, max. mold height: 970mm, oil capacity: 900l, connected load: 55kW, operating hours: approx. 82510h, weight: approx. 20.4t. The servo motor for the screw drive is defective. In addition, some smaller parts are missing. An on-site inspection is possible.

more

PUR Foaming Plant

Sunstar Engineering FOAMPLY T 1K Schaumanlage

Germany

2021

used

on request

INNO32235

A PUR foaming system with Yaskawa industrial robot is offered. Min. dispensing rate: approx. 0.15g/s, max. dispensing rate: 1.6g/s, material system: polyurethane Penguin Foam 3151/3157, drum capacity: 200l, operating voltage: 3 × 400V/N/PE, frequency: 50Hz, control voltage: 24V DC, upstream fuse: 16A. Approx. 30000 assemblies were foam-applied using the system. The system was shut down in 2024 according to the manufacturers instructions. Documentation available. An on-site inspection is possible.

more

Rubber Injection Moulding Machine

Klöckner Desma 968.400 ZO

Germany

1998

used

on request

INNO32210

A Klöckner DESMA rubber injection molding machine with increased clamping pressure is offered. Material processing: rubber, clamping force: 4500kN, min./max. mold height: 180mm/530mm, adjustable opening stroke: 570mm, clear distance between tie bars X/Y: 600mm/810mm, max. clamping area X/Y: 670mm/940mm, heating platen size X/Y: 670mm/940mm, injection: from above, max. injection volume: 3300cm³, injection force: 1886kN, max. injection pressure: 2150bar, screw diameter: 55mm, injection plunger diameter: 105mm, operating pressure: 250bar, number of control zones: 12, heating capacity per control zone: 21kW, ejector: hydraulic top and bottom, ejector slot spacing: 730mm. The machine is currently not operational because the control cabinet of the DRC 2000 (Simatic S7) is already being used elsewhere and is not part of the machine. Documentation available. Inspection possible by arrangement.

more

All Offers / Plastics processing machines