Innovac GmbH Used machines from Germany
Innovac used-machines Metal processing machines [1 - 20 of 927]
Vertical-Machining-Center-Buffalo-Machinery-Micromill-Challenger-MM-430 used
Vertical Machining Center
Buffalo Machinery Micromill Challenger MM-430
Germany
2011
used
on request
INNO29033
X-axis: 300mm, y-axis: 620mm, z-axis: 400mm, positioning accuracy: ±0.005 inch, repetition accuracy: 0.005 inch, rapid traverse: 25m/min, feed rate: 10m/min, air pressure: 6kg/cm², air consumption: 400l, pump motor: 30W, delivery rate: 2.2cm³/s, pump pressure: 8kg/cm², tank capacity: 2l, pump electrics: 220V/ 3PH/ 1.2A, max. delivery rate: 130l/min, control: Heidenhain TNC 620, connected load: 15kVA, length: 3000mm, width: 2050mm, height: 3020mm, weight: 3020kg. max. flow rate: 130l/min, control: Heidenhain TNC 620, connected load: 15kVA, length: 2984mm, width: 2050mm, height: 2420mm, weight: 3020kg. Operating hours control: 22,261h, machine: 22,414h, programme: 10,507h, spindle: 7695h. Fully functional, spindle was recently replaced, the built-in oil skimmer in the cooling water tank is not functional. With documentation. On-site inspection is possible.
Robot-Welding-Cell-Igm-RTE-497-S used
Robot Welding Cell
Igm RTE 497-S
Germany
2021
used
on request
INNO29032
Robot travel path: 5000mm, arm length: 2500mm, lift: 1000mm, spin radius: 2200mm, L-manipulator load capacity: 2000kg, lift velocity: 0,85m/min, swing speed: 1,7/min, turn speed: 6/min. Roboter type: IGM RTE 497-S in hanging position, control: full digital PC-Robotcontrol, Type RCE, software: WIN 10 & Linux based System + igm Robotsoftware K6, welding process: 135 (GMAW), single-wire, Ø1,2mm, welding power source: digital Invert Welding Power Source TPS 500i (500A at 40% duty cycle), robot periphery: rotating boom for floor installation with 2,5m boom length, number of working stations: 1, working station: 3-axis L-Manipulator with lifting device with 2t nominal load capacity, security Technology: Pistol-Security-Shut-down in wrist axis, emergency Stop on Handtablet, on Manipulators and Control Panel, three-coloured warning light for the operating Status partition, security Door. machine is complete, no defects known, documentation complete, was maintained regularly. An on-site inspection is possible.
Hydraulic-Press-Brake-Gwf-H-100-2 used
Hydraulic Press Brake
Gwf H 100-2
Germany
1992
used
on request
INNO26811
Compressive force: 1000kN/100t, ram stroke: 200mm, max. operating pressure: 290bar, control: DNC70, safety distance: 166mm, overtravel time: 104ms, overtravel distance: 7mm.
Punching-Machine-Trumpf-TRUMATIC-500 used
Punching Machine
Trumpf TRUMATIC 500
Germany
2000
used
on request
INNO29030
Max. Cutting force: 220kN, max. sheet thickness (steel): 8mm, max. sheet thickness (stainless steel): 4mm, max. punching diameter: 76.2mm, positioning speed X/ Y: 90/ 60m/min, compressed air connection: 6bar, fuse protection: 3x 35A, connected load: 19kVA, weight: 13.8t. On-site inspection is possible.
Flakkoting-Machine-Profin-BLUELINE-HFM-1-2-R used
Flakkoting Machine
Profin BLUELINE HFM 1/2-R
Germany
2010
used
on request
INNO23597
Suitable for edge preparation of all types of cutting tools with the corresponding holders and turning devices, e.g. roll cutters turning devices, e.g. cylindrical milling cutters, saw blades up to 380mm diameter, shank tools, indexable inserts and saw band coils up to 750mm diameter. Number of units: 1, table pitch circle: 600mm, table outer diameter: 800mm, machining width/height: 180/ 250mm, feed rate: 0.5-6m/min, flakkotier power: 4kW, connected load: 6.4kW, length: 2500mm, width: 1950mm, height: 2500mm, weight: 3t, operational hours counter: approx. 100h. Including documentation, without accessories or spare parts. On-site inspection is possible.
Bar-Loader-Kurt-Breuning-Irco-SIMAG-80.1-U-3000-II used
Bar Loader
Kurt Breuning Irco SIMAG 80.1 U/3000-II
Germany
2022
used
on request
INNO29023
Guide channel sets for diameters: 22, 42, 47, 52, 62, 67, connected load: 2.4 kVA, weight: 1.8 tonnes. Featuring short changeover times, easy handling, maximum running smoothness, hydrodynamic bearings, 360° closed guide channels, reliable feeding of rotationally symmetrical profile material. The machine has only been used a little, an on-site inspection is possible.
Plate-Shear-Durmazlar-DHGM-4006 used
Plate Shear
Durmazlar DHGM 4006
Germany
1996
used
on request
INNO29021
Working width: 41100mm, max. sheet thickness: 6mm, stroke: 131mm, stroke rate: 12/min, max. pressure: 150bar, oil tank capacity: 250l, control: ELGO Electric, motor power: 18.5kW, length: 4750mm, width: 2350mm, height: 1950mm, weight: 12t. On-site inspection is possible.
CNC-Machining-Center-Hermle-C-30 used
CNC Machining Center
Hermle C 30
Germany
2003
used
on request
INNO29020
X-axis: 650mm, y-axis: 600mm, z-axis: 500mm, max. spindle speed: 20-18,000 rpm, number of tool positions: 32, tool diameter: 90-125mm, max. tool length: 125mm, NC swivelling rotary table diameter: 630mm, rapid traverse: 45m/min, resolution of path measuring system: 0.0001mm, spindle power: 15kW, torque: 0.0001mm, max. tool length: 125mm, NC swivelling rotary table diameter: 630mm, rapid traverse: 45m/min, resolution of path measuring system: 0.0001mm, spindle power: 10/15kW, torque: 87/130Nm, tandem drive A-axis: 6m/s, compressed air connection: 6bar, control: Heidenhain iTNC 530, weight: approx. 12t. With tool breakage measurement, measuring probe, linear axes standard version, chip tray and other elements, new spindle head 2023.
CNC-Gear-Grinding-Machine-Bhs-hoefler-SUPRA-1603 used
CNC Gear Grinding Machine
Bhs-hoefler SUPRA 1603
Germany
1989
used
on request
INNO26321
Max. table load: 8t, diameter table: 2000m, max. wheel diameter wheel: 720mm, pressure angle: 12.5-30°, max. bevel angle: 35°, diameter grinding wheel: 300mm/400m, peripheral speeds: 25 or 35m/s, grinding stroke: 750mm, number of teeth: 12-372, length: 6800mm, width: 5500mm, height: 3800mm, weight: 26t, was modernized in 2000 and equipped with CNC control, with documentation, on-site inspection is possible.
Double-Column-Draw-Press-Müller-ZE-250-315 used
Double-Column Draw Press
Müller ZE 250/315
Germany
1978
used
on request
INNO29016
Pressing force: 3150kN, table dimensions: 1250x1100mm, table height: 750mm. Fully functional, last internal inspection: Q1/2025, UVV on Q2/2024. On-site inspection is possible.
Single-Column-Eccentric-Press-Müller-Weingarten-AR-100W used
Single-Column Eccentric Press
Müller Weingarten AR 100W
Germany
1969
used
on request
INNO29015
Press force cutting and drawing ram: 1000kN, table dimensions: 710x560mm, thickness of clamping plate: 90mm. Fully functional, last internal inspection: Q1/2025, UVV on Q2/2024. On-site inspection is possible.
CNC-Turning-and-Milling-Center-Niles-simmons-N30-2500-MC used
CNC Turning- and Milling Center
Niles-simmons N30/2500 MC
Germany
2002
used
on request
INNO29009
With two machining modules, X-axis: -50 to 725mm, Y-axis: -200 to 300/ -250 to 250mm, rapid traverse X-, Y-, Z-axis: 18/12/30m/min, turning lengths: 1500/2000/2500/3200/4000/4500/6500mm, swing diameter: 780/ 880mm, turning spindle bore: 92/123mm, main spindle speed range: 0-3000/0-3000/2000/min, max. Turning/milling unit speed: 5000/6000/10000/min, max. tool length: 900/600/1000/300/900mm, quill stroke: 160/170mm, connected load: 102kVA, control system: SINUMERIK ONE / SINUMERIK 840D sl, drive system control: SINAMICS S120, weight: 17t. On-site inspection is possible.
Laser-Marking-and-Engraving-Machine-Acsys-PIRANHA-I-FL20SEP used
Laser Marking and Engraving Machine
Acsys PIRANHA I FL20SEP
Germany
2020
used
on request
INNO29008
Z-axis: 390mm, max. workpiece dimensions: 730x450x440mm, max. workpiece weight: 100kg, internal surface dimensions: 520x375mm, connected load: 3500W, length: 990mm, width: 690mm, height: 1600mm, weight: approx. 550kg. The machine is as good as new and fully functional, without cooling system. An inspection is possible.
CNC-Cylindrical-Grinding-Machine-Danobat-UG51-1800-B2 used
CNC Cylindrical Grinding Machine
Danobat UG51-1800-B2
Germany
2006
used
on request
INNO29003
Available from June 2025, max. grinding length: 1800mm, max. grinding diameter: 448mm, min. grinding diameter: 10mm, max. angle of rotation: 10°, grinding wheel dimensions: 510x80x203.2mm, max. tool weight between centers: 500kg, grinding spindle power: 7.5kW, connected load: 25kW, control: GE Fanuc Series 210i, weight: 9.15t. The grinding spindle was re-stored in 2021, various spare parts for this assembly are available. Currently there is damage to the B-axis, the clamping is defective, for this reason a process-safe use of the measuring probe is currently not given, otherwise the machine achieves geometrically very good results. An on-site inspection is possible.
Forging-Hammer-Bêché-L6 used
Forging Hammer
Bêché L6
Germany
1931
used
on request
INNO26547
Bear weight: 300kg, lifting speed: 130/min, with documentation, an on-site inspection is possible.
Forging-Hammer-Bêché-L7 used
Forging Hammer
Bêché L7
Germany
1934
used
on request
INNO26546
Bear weight: 400kg, lifting speed: 125/min, connected load: 30kW, with documentation, an on-site inspection is possible.
Surface-Lathe-Ravensburg-P20-3 used
Surface Lathe
Ravensburg P20/3
Germany
1959
used
on request
INNO29002
Turning diameter: 1500mm, turning length: 2000mm, a Siemens panel control was installed in 2018. An on-site inspection is possible.
NC-Lathe-Giana-GFS-12 used
NC Lathe
Giana GFS 12
Germany
1977
used
on request
INNO29001
Turning diameter: 1200mm, turning length: 2000mm, speed: 6-178/ 20-600/min, control: Fagor NC. The machine was overhauled in 1999. On-site inspection is possible, available immediately.
Band-Saw-Kasto-SSB-260-VA used
Band Saw
Kasto SSB 260 VA
Germany
1985
used
on request
INNO29000
Saw blade length: 4115mm, cutting range round: 10-260mm, square: 260x260mm, connected load: 4kW, length: 2200mm, width: 2000mm, height: 2100mm, machine weight approx.: 5.2t. On-site inspection is possible.
CNC-Tapping-Center-Brother-Industries-TC-R2A used
CNC Tapping Center
Brother Industries TC-R2A
Germany
2006
used
on request
INNO28997
X-axis: 420mm, y-axis: 320mm, z-axis: 270mm, table dimensions: 500x300mm, spindle power: 7kVA, connected load: 20kVA, length: 1460mm, width: 2450mm, height: 3130mm, weight: 2.9t. The machine is defective and needs overhauling, on-site inspection is possible.