▷ Used plastics processing machines from Germany | innovac.de

Innovac GmbH Used machines from Germany

i.e. Machining Center MORI SEIKI

Innovac used-machines

Plastics processing machines [41 - 60 of 190]

Injection Moulding Machine

Krauss Maffei KM300-1900 C2

Germany

2000

used

on request

INNO31642

Clamping force: 3000kN, stroke volume: 1047cm³, shot weight: 953g, injection pressure: 1778bar, screw diameter: 70mm, tie-bar spacing: 630mm, opening stroke: 1150mm, ejector stroke: 200mm, installation height: 330mm, platen width: 1050mm, platen height: 995mm. Machine dimensions X/Y/Z: approx. 6250mm/2050mm/2400mm, weight: approx. 12500kg. Documentation available. An on-site inspection is possible.

Rubber Injection 'Molding Machine

Maplan MA/22

Germany

unknown

used

on request

INNO31616

An injection molding machine Maplan for elastomers requiring repair is available. Design: hydraulic vertical press, hydraulic oil type: ISO VH 46 HLP, hydraulic oil filling quantity: approx. 600l, max. hydraulic pressure: 250bar, heating cartridge diameter: 25mm, insulation plate thickness: 14mm, max. operating temperature: 250°C, L/D ratio: 12:1, max. back pressure: 400bar, max. stroke: 260mm, vacuum pump capacity: 63m³/h, weight: approx. 17500kg, control system: B&R PLC. The temperature control units and the hydraulic clamping system have failed. Documentation available. An on-site inspection is possible.

Injection Moulding Machine

Battenfeld HM 1600/1000

Germany

2002

used

on request

INNO31503

Clamping force: 1600kN, tie bar spacing: 570x520mm, platen dimensions: 810x805mm, max. mould diameter: 804mm, rotary table diameter: 735mm, min. installation height: 300mm, opening stroke: 650mm, opening force: 84kN, tie bar diameter: 80mm, max. daylight opening: 950mm, ejector force: 41.2kN, ejector stroke: 200mm, oil tank volume: 400l, standard drive power: 37kW, hydraulic operating pressure: 240bar, control system: Battenfeld Unilog B4, weight: 7.8t. An on-site inspection is possible.

Thermoformer

Gabler M92L

Germany

2007

used

on request

INNO25234

Forming surface: 750x436mm, heating output: 155kW, max. compressed air supply: 10bar, weight: 9.2t, operational hours counter: 43,589h.

Injection Moulding Machine

Sumitomo Demag EL-EXIS S 300/720-1450

Germany

2009

used

on request

INNO31486

Clamping force: 3000kN, locking force: 3300kN, max. opening stroke: 670mm, min. mould installation height: 330mm, max. mould installation height: 710mm, max. distance between mould platens: 1380mm, mould platen dimensions: 1040x950mm, distance between tie bars: 720x650mm, max. mould weight: 4.7t, max. weight on moving mould platen: 2.4t, max. weight on fixed mould platen: 3.6t, ejector stroke: 200mm, ejector force: 69kN, ejector return force: 31kN, screw diameter: 50mm, L/D ratio: 20, injection pressure at 400°C: 2426bar, shot volume: 530cm³, shot weight (PS): 480g, max. metering stroke: 270mm, max. nozzle stroke: 470mm, nozzle immersion depth (SVO): 20mm, nozzle contact force: 110kN, installed barrel heating capacity: 14.8kW, material hopper capacity: 110l, oil tank capacity: 700l, electric screw drive: 38kW, electric clamping unit drive: 37kW, pump unit power: 22kW, total installed power: 112kW, continuous sound pressure level: 78dB(A), length: 6500mm, width: 2000mm, height: 2300mm, weight: 15.7t, operating hours according to PLC: 28,890h, barrel heating: 35,656h, pump: 27,922h, documentation available. An on-site inspection is possible.

Injection Moulding Machine

Sumitomo Demag EL EXIS S 200/560-840

Germany

2009

used

on request

INNO31484

Clamping force: 2000kN, locking force: 2200kN, max. opening stroke: 570mm, min. mould installation height: 310mm, max. mould installation height: 660mm, max. distance between mould platens: 1230mm, mould platen dimensions: 830x830mm, distance between tie bars: 560x560mm, max. mould weight: 3.3t, max. weight on moving mould platen: 1.7t, max. weight on fixed mould platen: 2.5t, ejector stroke: 180mm, ejector force: 69kN, ejector return force: 31kN, screw diameter: 45mm, L/D ratio: 20, injection pressure at 400°C: 2402bar, shot volume: 358cm³, shot weight (PS): 330g, max. metering stroke: 225mm, max. nozzle stroke: 400mm, nozzle immersion depth (SVO): 20mm, nozzle contact force: 80kN, installed barrel heating capacity: 13kW, material hopper capacity: 70l, oil tank capacity: 500l, screw drive: 32kW, clamping unit drive: 32kW, pump unit power: 15kW, total installed power: 92kW, continuous sound pressure level: 74dB(A), length: 5700mm, width: 1700mm, height: 2200mm, weight: 11t, operating hours according to PLC: 36,734h, barrel heating: 25,665h, pump: 18,222h, documentation available. An on-site inspection is possible. A Wittmann robotic cell is also optionally available.

Injection Moulding Machine

Mir RMP 200

Germany

1999

used

on request

INNO31423

Ejector stroke: 180mm, ejector force: 44kN, nozzle contact pressure: 38kN, hopper capacity: 75dm³, mold clamping force: 1962kN, mold opening stroke: 560mm, length: 6275mm, width: 1520mm, height: 1965mm, weight: 8.3t. An inspection on site is possible.

Injection Moulding Machine

Engel EM 740/180HL

Germany

2007

used

on request

INNO31387

Clamping force: 1800kN, screw stroke: 200mm, speed: 300rpm, L/D: 20, nozzle stroke: 400mm, nozzle contact force: 50kN, hopper volume: 80l, tie-bar spacing: 520mm/520mm, platen dimensions X/Y: 760mm/760mm, mold installation height range: 250mm-600mm. Machine dimensions X/Y/Z: 6200mm/1700mm/2750mm, weight: approx. 12000kg, operating hours (Nov. 2025): 27271h. Including handling and protective enclosure. Documentation available. An on-site inspection is possible.

Injection Moulding Machine

Battenfeld HM 450/3300

Germany

2005

used

on request

INNO31364

Clamping force: 450t, opening stroke: 950mm, tie bar spacing X/Y: 800mm/970mm, operating pressure: 210bar, weight: approx. 20400kg, control system: Unilog B4. An on-site inspection is possible.

Granulator

Getecha RS2002-E00004

Germany

2003

used

on request

INNO31356

A compact Getecha edge trim granulator is available. Inlet opening X/Y: 254mm/305mm, drive power: 3.7kW. An on-site inspection is possible.

Injection Moulding Machine

Ferromatik K-Tec 85

Germany

2000

used

on request

INNO31331

Clamping force: 850kN, tie-bar spacing: 370mm/370mm, platen dimensions X/Y: 540mm/540mm, opening stroke: 450mm, machine dimensions X/Y/Z: approx. 4000mm/1300mm/2000mm, weight: approx. 4250kg. Some parts of the machine have been renewed in recent years. Documentation available. An on-site inspection is possible.

3D Printer

Keyence Agilista-3200W

Germany

unknown

used

on request

INNO31183

An inkjet-based industrial PolyJet/material jetting 3D printer Keyence for photopolymers is available. Build volume dimensions X/Y/Z: 297mm/210mm/200mm, resolution: 635dpi/400dpi, XY resolution: 63.5µm/40µm, layer thickness range: 15µm-30µm, machine dimensions X/Y/Z: approx. 950mm/700mm/1400mm, weight: approx. 200kg. Documentation available. An on-site inspection is possible.

Injection Moulding Machine

Battenfeld TM 4500/3300

Germany

2004

used

on request

INNO31159

A large-format horizontal injection molding machine Battenfeld is available. Operating pressure: 210bar, clamping force: 4500kN, screw diameter: 85mm, injection volume: 2128cm³, injection pressure: 1624bar, tie-bar spacing: 900mm/800mm, opening stroke: 950mm, max. mold installation height: 970mm, oil volume: 900l, connected load: 55kW, weight: approx. 20400kg. Documentation available. An on-site inspection is possible. The machine has a defect.

Injection Moulding Machine

Dr. Boy 50T2 185-50

Germany

1992

used

on request

INNO31086

An injection molding machine Dr. Boy is available. Clamping force: 500kN, tie-bar spacing: 305mm/305mm, platen dimensions X/Y: 500mm/500mm, max. opening stroke: 350mm, max. platen spacing: 600mm, min. mold height: 250mm, max. screw stroke: 120mm. Machine dimensions X/Y/Z: approx. 3450mm/1050mm/2000mm, weight: approx. 2050kg, operating hours: 10524h. The system has minor defects requiring repair. Documentation available. An on-site inspection is possible.

Cooling System

Green Box Twin 26/HP

Germany

2012

used

on request

INNO31045

An air-cooled monoblock water chiller Green Box for the plastics industry is available. Cooling capacity: approx. 20 injection molding machines, power: 25kW, refrigerant circuits: 2, refrigerant: R407C, cooling capacity: approx. 80kW, air flow rate: approx. 16500m³/h. Machine dimensions X/Y/Z: approx. 3300mm/1100mm/2100mm, weight: approx. 1300kg. Documentation available. An on-site inspection is possible.

CNC Laser Cutting Machine

Eurolaser LCS XL-1600

Germany

2010

used

on request

INNO31044

A CO2 laser cutting and marking machine Eurolaser, which was used for acrylic glass, is available. Laser power: 200W, working dimensions X/Y: 2270mm/1600mm, max. cutting width: 2200mm, material feed width: 2350mm, table feed-through height range: 58mm-80mm, engraving resolution: 1200dpi, grayscale levels: 256, material processing: films/textiles/plastics/composite materials/paper/thin wood. Machine dimensions X/Y/Z: approx. 4000mm/2350mm/1600mm, weight: approx. 2000kg. The laser source was renewed in 2017. Documentation available. An on-site inspection is possible.

Granules Dryer

Arburg Thermolift 100-2

Germany

1999

used

on request

INNO31018

An Arburg plastic granulate dryer with integrated material conveying is available. Hopper volume: 100l, max. drying temperature: 150°C, heating capacity: 4.5kW, air capacity: 90m³/h, conveying height: approx. 3000mm, machine dimensions X/Y/Z: approx. 950mm/600mm/2000mm, weight: approx. 150kg. An on-site inspection is possible.

Dosing and Casting System

Respecta Epoxidharz

Germany

2019

used

on request

INNO30997

A complete Respecta epoxy resin metering and casting system is available. 1) Big bag station for supplying fillers, max. particle size: 0.7mm, max. bulk density: 0.5g/cm³. 2) Two IBC connections for liquid components A and B with diaphragm pumps. 3) Two buffer tanks for A and B, volume: approx. 230l. Including level sensors and automatic IBC filling. 4) Volumetric metering to the mixing screw with flow meter and pressure monitoring. 5) Degassing unit. 6) Continuous epoxy resin inline heater with process monitoring of the resin temperature and the epoxy hardener, viscosity range: approx. 350-450mPas, max. epoxy resin temperature: 20°C. 7) Semi-automatic flushing and cleaning unit for the casting unit, volume: approx. 50l. Overall system control: Siemens Simatic S7, additional controls: control cabinets/frequency converters/industrial PC, overall system casting capacity: approx. 30l/min. The system allows mechanical preparation for retrofitting up to 3 additional filler metering systems. It is recommended to renew the lines and the diaphragm pumps before commissioning. Documentation available. An on-site inspection is possible.

PU Cutting Machine

Westema STV-492

Germany

1990

used

on request

INNO30982

A Westema cutting table for precise cutting of soft, flexible materials is available. Table dimensions X/Y: 2250mm/1500mm, max. cutting height: 230mm, cutting speed: 16m/s, motor power: 1.1kW. Including quick clamping and grinding device. Documentation available. An on site inspection is possible.

Corona Pretreatment System

Ferrarini & Benelli S 200

Germany

1999

used

on request

INNO30930

A Ferrarini & Benelli corona pre-treatment system for surface activation of non-conductive materials in continuous production processes is available. Generator type: C15/4N, output frequency: 15kHz, electrode design: multi-cylinder roller electrodes, max. treatment width: 200mm. An on-site inspection is possible.